E900 Barcode Scanner Support Guide

This page primarily collects and categorizes configuration methods for barcode scanners. You can click to jump to the specific operation page based on your required issue.

System Information / Device Info

Information about firmware, system, module identity.

Power Management

Battery, sleep, power modes, energy.

Scanning / Triggering Behavior

How the engine reads, detects, or stays idle.

Symbology Type Settings

Enable/disable barcode types or adjust their rules.

Data Formatting & Output Rules

All data manipulation after decoding.

Character Encoding / ASCII / Control Characters

All encoding and special output rules.

Interface Settings (Wired)

Communication settings for physical interfaces.

Wireless Communication Settings

Standard wireless modules used in engines.

Hardware / Physical Interface

Sensor and device hardware functionality.

Error Handling / Fault Recovery

How the device handles faults.

Firmware & Software Tools

Update and development tooling.

Model-Specific Configuration Articles

Additional settings that apply to this scanner model.

System Information and Settings

Information about firmware, system behavior, defaults, lighting, sleep, and device feedback.

• A code reading timeout
• Automatic sleep
• Brackets around GS1 Application Identifiers (GS1AIs)
• Decode mode
• Decoding timeout
• Exterior lighting
• Factory default
• How to enable or disable code reading
• How to modify the startup code reading command
• How to modify the stop reading command
• How to modify the unsuccessful code reading information (NGR information)
• Image flip
• Image stabilization timeout (sensing mode)
• Query data format and edit version number
• Query hardware information
• Query product name
• Query product OEM serial number
• Query product production date
• Query product serial number
• Query system information
• Reading preferences
• Reread delay
• Reread timeout reset
• System information content:
• The aiming light
• The beep sound
• The boot tone
• The center area
• The code reading success delay
• The code reading success delay time
• The decoding center area
• The decoding success LED light
• The decoding success LED light duration
• The decoding success sound
• The decoding success sound frequency
• The duration of successful decoding sound
• The firmware version number
• The light
• The lighting lamp
• The lighting LED
• The message of unsuccessful code reading
• The query decoder version number
• The reread delay time
• The sensor sensitivity
• The serial trigger command
• The sound volume of successful decoding
• User default

Communication Settings

USB, RS-232, serial, keyboard, and host communication settings.

• Caps Lock
• Case conversion
• Communication cable adaptation
• Control character output
• Fast mode
• IBM SurePOS (Hand-Held)
• IBM SurePOS (Table-Top)
• Key delay
• Keyboard emulation input characters
• Polling speed
• Scanning data
• Sending data to the device
• The analog numeric keypad
• The control character correspondence table
• The control character correspondence table (continued)
• The national keyboard layout
• The VID and PID table
• Unknown character prompt sound
• What to do with USB CDC serial port

Data Formatting & Output Rules

Output rules and data formatting after decoding.

• Move command
• Other commands
• The added data format
• The clear data format
• The data format editing command
• The data format mismatch error tone
• The search command
• The selection data format
• The send command
• The single-use data format
• Turn on or off data format editing

Barcode Symbology Settings

Enable, disable, length, check digit, and other barcode type settings.

• AI (01) character transmission
• Code32 Pharmaceutical (PARAF)
• Conversion to EAN-13
• Conversion to UPC-A
• Coupon GS1 DataBar output
• Data Matrix dual code
• Data Matrix inversion
• EAN-13. There must be an extension code starting from 290
• EAN-13. There must be an extension code starting from 378/379
• EAN-13. There must be an extension code starting from 414/419
• EAN-13. There must be an extension code starting from 434/439
• EAN-13. There must be an extension code starting from 977
• EAN-13. There must be an extension code starting from 978
• EAN-13. There must be an extension code starting from 979
• ECI output
• Full ASCII
• Hansein code double code
• Hansein code inversion
• ISBN format
• One-dimensional barcode dual code
• PDF 417 inversion
• PDF417 dual code
• QR dual code
• QR inversion
• Rectangular code
• The bit extension code
• The character encoding method
• The extension code that must be appended
• The reading length
• The start character and suffix terminator
• The start character and suffix terminator format
• The transmission check character
• The transmission leading character
• To allow all 1D codes
• To allow all 2D barcodes
• To allow all barcodes
• To allow all postal codes
• To restore factory default
• Turn on or off all 1D codes
• Turn on or off all 2D barcodes
• Turn on or off all barcodes
• Turn on or off all postal codes
• Turn on or off reading USPS Intelligent Mail
• Turn reading on or off
• UPC/EAN version
• UPC-A/EAN-13 with Coupon extension code
• UPC-E0
• UPC-E1
• Verification

Other Configuration Settings

Additional configuration articles for this model.

• Batch barcode production
• Batch processing barcode
• Batch processing instructions
• Data bit transmission
• The baud rate
• The parity character
• The stop bit